Stair Nose Installation

The Perfect-Match Stair Nose caps the exposed front edge of a stair tread with a full-radius bullnose, colour-matched to the same décor as your SuperOak planks. It bonds to the tread you already have. The same piece and the same method apply across the LITE, SELECT, PLUS and ELITE ranges.

SuperOak SELECT Perfect-Match Stair Nose

What this piece is

It is

A 3-inch-wide overlay for the front edge of an existing, structurally sound tread.

It is not

A full stair tread. To resurface the whole tread, use the Stair Tread Perfect-Match-Trim — 48 in. × 12.2 in.

It is not

A track-and-snap trim. Reducers and T-moldings use a PVC track; the stair nose does not.

Specifications

Length 47 in. — cut to fit each stair
Width 3 in.
Thickness approx. 1/2 in. at the cap
Front profile Full-radius bullnose, curving down over the front of the tread and returning underneath
Core Waterproof SPC
Finish Factory-finished — no painting, staining or sealing
Coordinates with SuperOak LITE, SELECT, PLUS and ELITE — colour-matched per range
Sold Individually — one piece per stair
Grade Above, on or below grade; residential and light commercial

Cross-section

3 in. width ~1/2 in. ~1-1/2 in. nose radius Adhesive — held back from the front edge Existing tread Riser 47 in. length runs into the page
Section through one stair, drawn to scale. The radius wraps the front of the tread and returns underneath; the adhesive sits back from that edge so it cannot squeeze out onto the finished surface.

Site conditions

Relative humidity35 – 65 %Climate-controlled space only
Temperature60 – 85 °FHeld before, during and after install
Tread flatness3/16 in. / 10 ftCorrect high or low spots first
Tread conditionDry · sound · cleanNo wax, dust or loose finish

Tools

  • Tape measure and square
  • Fine-tooth blade — miter or circular saw
  • Construction adhesive and caulk gun
  • Painter's tape or stair weights
  • Utility knife
  • Denatured alcohol and clean rags
  • Safety glasses and dust mask

Installation

  1. Acclimate the material

    Bring the pieces into the room where they will be installed and leave them lying flat for 48 hours. Do not stand them on end.

  2. Prepare each tread nose

    Strip any carpet, tack strip, staples or old nosing. Scrape the front edge flat, vacuum it, then wipe with denatured alcohol and let it flash off. Adhesive will not hold on wax or a loose finish.

  3. Measure every stair separately

    Stairs are rarely identical. Measure each one at the front edge, not at the back, and mark the piece for that specific stair. Stock length is 47 in.; a wider stair takes two pieces with the seam placed off-centre.

  4. Cut finished-face up

    Use a fine-tooth blade with the décor side facing up so the wear layer does not chip. Where the piece meets a skirt board or wall, scribe it rather than force it, and leave about 1/8 in. at each end.

  5. Dry-fit before any adhesive

    Set the piece in place and check that the radius sits tight against the front of the tread along the whole length, with no rock and no daylight under the cap. Correct the tread, not the trim.

  6. Apply adhesive

    Run a continuous serpentine bead across the bearing surface, holding it back about 1/2 in. from the front edge and from each end so nothing squeezes out onto the face or the riser.

  7. Set it front-edge first

    Land the radius against the front of the tread first, then lower the back of the cap and press the full length down. Working front-to-back keeps the visible edge tight and pushes any excess adhesive backwards, out of sight.

  8. Weight it and let it cure

    Tape or weight the piece along its length and keep all traffic off the stair for the adhesive manufacturer's stated cure time. Wipe any squeeze-out immediately — cured adhesive will not come off the wear layer cleanly.

  9. Finish at the landing

    Where the top stair meets a floating SuperOak floor, leave the floor's expansion gap intact and cover it with the trim. Fasten into the stair, never through the floating floor.

Do not

  • Do not fasten or glue through a floating floor. The field floor has to stay free to move; pinning it at the stair will buckle it elsewhere.
  • Do not install over a soft, hollow or delaminating tread. The stair nose is a finish overlay and carries no structural load — repair the tread first.
  • Do not use the stair nose as a full tread. It covers the front edge only.
  • Do not paint, stain, sand or seal it. The wear layer is the finish; sanding it voids the warranty.
  • Do not install outdoors, in an unheated space, or anywhere outside the 35–65 % RH range.

SELECT colours

The twelve SELECT colours are shown below; LITE, PLUS and ELITE each carry their own range. Each colour is matched to the plank of the same name. The grain reads finer on a 3-inch face than on a 7.68-inch plank, and a printed décor varies slightly batch to batch — order a sample to confirm the match before committing to a full staircase.

SuperOak SELECT Perfect-Match Stair Nose in Antique Oak
Antique Oak
SuperOak SELECT Perfect-Match Stair Nose in Brown Knots
Brown Knots
SuperOak SELECT Perfect-Match Stair Nose in Clean Brushed
Clean Brushed
SuperOak SELECT Perfect-Match Stair Nose in Dark Oak
Dark Oak
SuperOak SELECT Perfect-Match Stair Nose in Gray Oak
Gray Oak
SuperOak SELECT Perfect-Match Stair Nose in Light Canoy
Light Canoy
SuperOak SELECT Perfect-Match Stair Nose in Natural Clean
Natural Clean
SuperOak SELECT Perfect-Match Stair Nose in Noon Hickory
Noon Hickory
SuperOak SELECT Perfect-Match Stair Nose in Plain Brown
Plain Brown
SuperOak SELECT Perfect-Match Stair Nose in Plain Driftwood
Plain Driftwood
SuperOak SELECT Perfect-Match Stair Nose in Riftwood Knot
Riftwood Knot
SuperOak SELECT Perfect-Match Stair Nose in Sunshine Hickory
Sunshine Hickory

Care

Clean with a damp mop and a pH-neutral floor cleaner. No steam, no wax, no abrasive pads.

View the SuperOak SELECT Perfect-Match Stair Nose →

ONE STOP DELIVERY

Our one-stop production process is designed to deliver high-quality, cost-effective products efficiently to our customers. By streamlining every step, from design to manufacturing, we eliminate unnecessary middlemen and reduce overhead costs. This means we can offer affordable pricing without compromising on quality. Additionally, our advanced production methods ensure fast turnaround times, allowing us to bring products to market more quickly and meet customer demands efficiently.

Regional distribution from our California and South Carolina warehouses keeps lead times short and support close to the customer.

Diversified Materials

The Benchwick 3D Printing ECOSYSTEM is a revolutionary platform that offers exceptional versatility across a wide range of materials and substrates in home improvement. From flooring to wall panels, it supports diverse materials like wood, stone, and hybrid composites, and works seamlessly with substrates such as self-innovated Blue11, vinyl, and rigid core and wood.

This proprietary technology enables precise customization, creating highly realistic textures and designs while ensuring durability and ease of installation. Whether for residential or commercial projects, Benchwick’s 3D ecosystem provides an eco-friendly solution that combines beauty, functionality, and sustainability to transform any space.

Global Proprietary

The Benchwick 3D Printing ECOSYSTEM is a globally recognized, proprietary technology platform that redefines the creation of flooring and wall solutions. With its own protected intellectual property portfolio, Benchwick stands at the forefront of innovation, offering patented 3D printing processes that produce stunning, customizable designs. These designs authentically replicate the textures and aesthetics of natural materials like wood and stone, delivering superior quality and durability.

By leveraging its exclusive global intellectual properties, Benchwick ensures that its advanced technology is unmatched in precision, sustainability, and efficiency. The ecosystem not only accelerates production times but also reduces waste, making it an eco-friendly solution for modern spaces. Operating on a global scale, the Benchwick 3D Printing ECOSYSTEM is poised to transform both residential and commercial environments through its unique, cutting-edge, and proprietary innovations.